5 x Push in Electrical Cable Wire Connector Easy Clip and Lock for Downlight Can, LED Panel, Batten Tube Light PA1243F

Product Information

At this point you will have the connected downlights hanging from the ceiling. All that remains is insert the light into its place in the ceiling. Typical heights for 80mm cut out lights are in the region of 75 – 110mm typically, although it is possible to find “low profile” models should space be really tight. It’s also essential that the correct cable is used. In most cases 1mm twin and earth should be fine but if it’s a particularly long circuit, there are many lights or they are particularly powerful then 1.5mm twin and earth will need to be used. The electrician doing the work will know exactly what to use. Strip the ends of the wires in your wall and on the downlight. Open the wire stripper and clamp the last 1⁄ 2 inch (1.3 cm) of the 14/2 cable between the jaws. Pull the strippers toward the end wire to remove the insulation. Repeat the process with the wire attached to the downlight. [13] X Research source

Measure the rear diameter of the light to know the size of the cut out. Set the light down so the bulb is on the bottom and the part that would be inside your ceiling points up. Use a tape measure to find the diameter of the light so you know how large the hole needs to be. Don’t measure the side of the light that has trim around it, or else you’ll cut the hole too large. [6] X Research source Yes, you can replace old downlights with an LED alternative. However, getting an electrician to do the changeover from halogen to LEDs is advisable. If you're not knowledgeable about lighting and electrics, leaving it to the professionals to guarantee correct and safe installation is better. You can instead do the replacement of the LED bulbs once your fixture is already transitioned to an LED one. I have a brite source led downlight driver connector box for the brite source 833839 led downlight that I am trying to disconnect the cables from. They go into a push fit connector - so look like they get pushed in and then you push a connector down to hold the cable in. Apart from breaking the connectors (already done that once) I am not too sure how I can get the wires out. While energy efficiency and eco-friendliness are some of the attention-grabbing perks of an LED, the one that seals the deal are their low maintenance quality and extended lifespan. Once you install it, you don't need to do anything else afterwards. Just clean it regularly to remove dust and dirt, and you're done! Also, this lighting unit can last for 50,000 hours, so you don't have to replace them for years.Now we’ve got the important safety information out the way, let’s get on with the rest of the information. Types of Downlights Mains voltage is 230V AC and has a tolerance of 10%, some products are 220V or 240V AC which means they can be classed as mains voltage. Halogen lights were a huge technological leap forward in their day, however they are only about 30% more efficient than old fashioned incandescent bulbs and will only last about 2 years (based on 3 hours usage everyday). They also get hot so consideration needs to be given to ventilation. Use a stud finder to locate the joists in your ceiling. Turn on the stud finder and hold it flat against your ceiling. Slowly move the stud finder across your ceiling until it beeps or lights up. Mark the location where it beeps with a pencil to mark the edge of the joist. Continue working across your ceiling in the area you want to install your downlight so you know the areas to avoid putting the lights. [1] X Research source

You can expect your LED downlight to last for around 50,000 hours, although you may need to replace them at some stage. Regarding the process of removing a LED bulb, this is a fairly similar approach to removing a downlight. Although when thinking of downlights you may automatically think of the recessed type we have mentioned above, it’s also common to categorise the surface mounted spotlight cluster as a form of downlight as, although they are mounted in an external unit fixed to the ceiling, they still actually use downlights as their lighting source. How can you tell if a downlight is fire-rated or not? The easiest way to find out is by reviewing the product description or technical specification. Read through it carefully and ensure that it's explicitly stated. If you're still unsure, ask the salesperson to direct you to the fire-rated downlights section if you're shopping personally or go to the specific category if you're buying online.LED recessed downlights are an eco-friendly choice since they contain no hazardous elements like tungsten or mercury. It's safe for the environment and healthier to use for your family. Also, it produces less heat, so it won't make your room feel warmer, and even if you accidentally touch the bulb, you won't get burned, unlike with traditional lights.

Downlights serve as a versatile light fitting that proves to offer several versatile uses throughout a plethora of different rooms. These are also a great way to create zones, navigate around the space of a room and highlight key areas - such as artwork or photos. Run wires through your walls to the spot you’re installing the light. You can either attach the lights to an existing switch or you can add a new switch on your circuit. Feed a 14/2 cable through the wall using a wire tape so it lines up with the area where you’re placing the light. The 14/2 cable contains 1 hot wire, 1 neutral, and 1 ground. Additionally, as downlights are mostly installed in kitchens and bathrooms then these are regarded as “special locations” and the electrics in areas such as these can only be worked on by, again, a Part P registered electrician.Choose a downlight that’s short enough to fit in your ceiling. Downlights usually have a tall cylindrical shape so the bulb recesses into your ceiling. Usually, your ceiling will have 6 inches (15 cm) of space behind it, but it may vary depending on the age of your home. Get a bulb that has LEDs and emits about 35 watts so it’s bright enough for your room. [5] X Research source In regards to the number of downlights that you need, this is dependent on which room they will be used and for what purpose they will serve. For example, will they be used as the primary lighting source or for a particular task? You may wish to install an LED downlight as the primary lighting source across your living room or to highlight your food preparation area in your kitchen. As they are fixed they only project light straight downwards but as long as they are sensibly spaced across a ceiling then they will project more than enough light to prevent any shadows or shaded areas.