RotoZip GP8 1/8-Inch Guide Point Drywall Cutting Zip Bit, 8-Pack

Product Information

I wouldn’t buy a reciprocating saw just to cut drywall, but if you already have one on hand, purchasing a drywall blade can help you get even more use out of your existing tool. An ergonomic handle (I bought the cheaper version with a terrible handle and will definitely upgrade if/when this one wears out) Before you hang any of your drywall, you want to make sure that the power to any electrical boxes you’ll be near is turned off. To use a multitool to cut drywall, align your blade with the mark of where you want to cut on your drywall. Then, slowly squeeze the tool to start cutting- faster is not better. Use as much speed as you need to get through the material, and no more. Below, I’ve put together a list of some of the best ways to cut drywall and the tools you’ll need to get it done – each has its own pros and cons. Read on to find out where to buy the best tools, how to use them, and how to avoid mistakes before they happen when you’re cutting drywall for your next project. Table of Contents

Jigsaws are pretty intuitive to use, but I’ve found they’re best when starting from the edge of material, or within a pre-cut plunge hole – they don’t do plunge cuts very well. And start slow – remember, more speed isn’t better! #7: Hole Saw Cutter After you’ve cut your drywall to size and cut out any spots for lights or outlets using the methods listed above, attach the sheets of drywall to the studs and framing of your walls with drywall screws.

What's Included

A good utility knife or razor knife is essential to nearly every drywall project – even if you aren’t sure you’ll need it, make sure you have one on hand. What To Look For In A Utility Knife or Razor Knife to Cut Drywall If you need to make a bunch of plunge cuts and you already own a reciprocating saw, a reciprocating saw is a great choice for drywall work (even if it is little overpowered). What To Look For In A Reciprocating Saw to Cut Drywall

As with any project, measure twice (or three times, or four to be safe) and cut once. Drywall is messy, and the less dust you expose yourself to, the better. When To Use A Utility Knife or Razor Knife to Cut Drywall

Features

Something that accepts 1/8 inch and 1/4 inch bits so you’re not limited to certain cutting applications Much like a utility knife, a drywall or jab saw is great for small, straight cuts into drywall. That being said, it can do rough curved cuts, you’ll just have to be quite careful. Once you’ve scored one side of your drywall, turn the board over and add some gentle pressure along the scoreline – it should cleanly break away. #2: Keyhole Saw, Compass Saw, Jab Saw, or Drywall Saw (Handheld Drywall Saws) If you are cutting a large hole in drywall, it may be easier for you to use a power tool, like a reciprocating saw, or an oscillating multi-tool. If you’re operating in a smaller area, such as cutting drywall for an outlet, you may opt for something lighter, like a utility knife or a keyhole saw.

If you’re planning a big drywalling job, a spiral saw can save you tons of time, especially when cutting openings like for an electrical box or hanging a light fixture. When To Use Spiral Saw or Rotozip to Cut Drywall

Specifications

The blades on most handheld drywall saws are longer than what you’d generally need. I’ve not used them, but I know you can also find retractable drywall saws, like this one, that allow you to extend the blade only as far out as you need for your project. #3: Oscillating Multitool Reciprocating saws are probably a little overpowered for drywall work, but they can certainly help you get the job done – especially if you use a specialty drywall blade like this instead of a normal reciprocating saw blade.

If you’re on a budget, these disposable masks work well! Just make sure you get a snug fit around your nose.

If you already own a reciprocating saw and need to make a large volume of rough cuts (just make sure to get the drywall blade!)