Stormsure Boot, Shoe and Wader Repair Kit Clear 5g

Product Information

NatWest, Royal Bank of Scotland (RBS) and Ulster Bank, which are all part of the NatWest Group, will now shut at least 172 of their bank branches in 2023 and 2024.

Pay attention when considering what adhesive to use on your wellies because some, such as super glue, may not work with particular types of rubber. Using the bicycle tire repair kit method is effective when done properly and should result in watertight wellies you can use to walk through puddles; however, it may not be enough to wade through strong streams of water. It’s not uncommon for Wellington boots, commonly referred to as wellies, to develop a tear in the upper section. Most people end up throwing them out when this happens, but there’s no reason to trash your best Wellington boots when they get older. If you've repaired a puncture on a bicycle tire, you'll find fixing a tear in your wellies pretty straightforward. Even amateurs should have no problem if they follow the instructions in the bicycle tire repair kit. Steps in Fixing Wellies Keep Stormsure in a cool dry place away from incompatible materials, direct sunlight and sources of ignition.

Use the rubber solution or adhesive that comes in the kit. Apply a very thin layer and leave it for 2-3 seconds. Next, take the patch you have made and gently place it on top of the solution or adhesive. Ensure that the edges have been pressed down firmly.

The kit contains a 5g tube of Stormsure Flexible Repair Adhesive, two 75mm (diameter) TUFF Tape patches, along with protective gloves. Just as you might do with a bicycle tire patch, you may find that you may need to patch the area of your boot regularly if you want to extend the life of your wellies. You should also familiarise yourself with how to store Wellington boots to ensure they last even longer. PRO TIP: Aquaseal SR is also great for fixing delaminated soles, building toe caps, flexible knee patches, and rebuilding worn soles.

Use A Puncture Repair Kit

If your edges aren’t flush with the boot, add even more adhesive. If you don’t have enough adhesive, you will need to buy some glue. Be aware that repairing Wellington boots or any type of footwear requires the right glue. Using the wrong type of glue could result in a bad repair. As a result, you may have to start over. Apply some Chalk If you’re not sure how much you need to cut, cut a patch of rubber that’s a little bigger than the hole or split. Apply A Thin Layer of Adhesive Stormsure Flexible Repair Adhesive can repair everything from worn material to a large hole. Repairs are waterproof, flexible and resistant to abrasion (weather and water abrasion). Allow 24 hours for the adhesive to cure. It should be strong enough not putting etc grooves in but as it is in the area that bends a lot any extra strength will help. If you have invested in a quality pair of wellies, it is worth looking after them so that they continue to perform as you would expect.

The follow up support has been just as good and will definitely be using Stormsure the company and Stormsure glue again with lots of other things.To re-attach soles to uppers squeeze Stormsure into the affected area and place the boot on a flat surface and place a weight inside the boot to hold the repair together. Remove the weight after 12 hours. Apply Stormsure directly to the area, allowing an extra 5mm around the damaged area. Keep flat and allow to cure. Stormsure is touch dry in 2-4 hours. Allow 10-12 hours for full cure. I wondered if there was anything I could get that I could just run along the seam and maybe repair the leak? Something like a kind of glue, or silicone? Stormsure is the main brand from Stormsure Ltd. Stormsure Flexible Repair Adhesive is the Flagship product and where Stormsure begin it's journey 20 years ago. Stormsure Flexible repair Adhesive is our very own formula which works differently to almost all other adhesives on the market today. It's polyurethane composition and moisture curing properties make it completely waterproof, extremely durable and very very strong making it the perfect solution for almost any repair!

When fixing wellies using the tape method, the gaffer tape is effective in repelling water. The boots will withstand light tasks such as working in the garden and walking in puddles, but the tape is bound to peel off after regular soaking. Prep your leaky rubber boot by cleaning it first. Remove all dirt and grime with a low-suds soap like Revivex Boot and Shoe Cleaner and following these cleaning instructions.Cleaning your Hunter wellies is a crucial step in maintaining their pristine appearance and keeping them free from dirt and grime. To clean your wellies effectively, follow these simple steps: Try to store your boots out of direct sunlight and away from any heat sources, such as radiators or hot water pipes. The good news is that chalk is usually provided with every puncture repair kit. Wait until the adhesive has dried before you add any chalk or else you’ll create a bit of a mess on your wellies. Once it has dried nicely, add some chalk around the area that you applied the patch to. Your Repaired Wellington Boots As the boots that we sell are all made from 100% natural rubber, they will naturally deteriorate with time.